Value Processing Behaviors Animation Value Processing Behaviors Jump to Animation Keyframe Expects a Float value between 0 and 1 (inclusive) as an event. Sets a selected animation to a frame corresponding to the value that the AnimationProcessValueBehavior receives. Common Properties Property Name Type Description Animation SharedPointer The animation controlled. AnimationProcessValueBehavior sets the animation to the frame corresponding to the value it receives. SequenceStartTime FeatStd::Optional The start point of the animation. [ms] SequenceDurationTime FeatStd::Optional The duration of the animation. [ms] ControlNode Candera::AbstractNodePointer Diagnostics Value Processing Behaviors Frame Measurement Class Reference Outputs Frame Measure information of the specified Render Target. These Measurements can be Frames Per Seconds, Current Frame and Frame Time. This Behavior acts as Source for Process Value Behaviors. Common Properties Property Name Type Description RenderTarget Candera::GraphicDeviceUnit* The render target which FPS should be monitored. Output OutputType::Enum Specifies which information will be output. DispatchThreshold FeatStd::Optional< FeatStd::Variant > Specifies how much the Output has to change to dispatch an event to its receivers. Receivers Candera::ProcessValueBehaviorArrayProperty The process value behaviors that will receive the value as next in the value processing chain. This property can be set in the right side of the Scene Tree panel. Effects Value Processing Behaviors Set Alpha Value Sets the Alpha value of a node (expects a Float value). Common Properties Property Name Type Description Target Node Candera::AbstractNodePointer The Node which gets the resulting alpha value. If not set, then the node where the behavior is attached to, will be modified. Switch Image Sets an image on a Render Node based on a float index received as event. Supports Controls: FlipBook Example Usage Switch Image Example Common Properties Property Name Type Description Upload Strategy Enum (OnInit, OnDemand) Specifies if images are uploaded on demand or when the behavior is instantiated. OnInit may cause an initial delay and keeps all images loaded. OnDemand avoids an initial delay and only keeps one image loaded. Possible values: OnInit, OnDemand Target Node RenderNode * The Render Node SwitchImageProcessValueBehavior will switch images on. Images SharedPointer A list of images which should be available for selection. This property is only available for 2D scenes. Textures SharedPointer A list of images which should be available for selection. This property is only available for 3D scenes. OutOfBoundsHandlingMode OutOfBoundsHandlingMode::Enum Behavior when an index greater than the number of images is given. Possible values: Hold, Clamping Switch Text Sets a text on a Render Node based on a float index received as event. Common Properties Property Name Type Description Target Node Candera::AbstractNodePointer The Render Node SwitchTextProcessValueBehavior will switch the text on. Texts ArrayProperty Use list of texts (strings) and switch between them. Zoom Effect Expects a Float value between 0 and 1 (inclusive) as an event. Applies scale and alpha on children of a group. Common Properties Property Name Type Description Target Node Candera::AbstractNodePointer The node whose children are enabled or disabled by ZoomProcessValueBehavior. If not set, then the node where the behavior is attached to will be considered. Alpha Factors Vector2 Min/Max transparency factors Zoom Factors Vector2 Min/Max zoom factors Zoom Distribution Float Distribution of Zoom/Alpha to each side of the selection. ZoomByLayout bool Whether the zoom is accomplished by layout size. Transformation Value Processing Behaviors Resize Group Node Expects a Float value as an event, and changes the layout size of a group node it is placed on. When mode is 'Relative' it scales the layout size (expected value is a normalized value). When mode is 'Absolute' the layout size is set in pixels. Common Properties Property Name Type Description AffectXAxis bool Enables or disables scaling in horizontal direction. AffectYAxis bool Enables or disables scaling in vertical direction. Mode Mode::Enum Determines how the received value will be interpreted. ScaleVector Vector2 This vector is multiplied by the received value and specifies the magnitude by which the node is scaled. Set Node Size Expects a Float value as an event. Sets the layout size of a node on a given axis by the received value in pixels. Common Properties Property Name Type Description Target Node Candera::AbstractNodePointer The target node which is modified. if not set, then the node where the behavior is attached to, will be modified. Size Axis AxisType2D::Enum  The axis along which the size is set. Possible values: AxisX, AxisY Set Position Expects a Float value as an event. Translates Position Node along given axis by the received value in pixels. Example Usage Set Position Example Common Properties Property Name Type Description Target Node Candera::AbstractNodePointer The target node to which the events are routed from the source node. Translation Axis 2D AxisType2D::Enum The axis along which the position is set. Possible values: AxisX, AxisY This property is only available for 2D scenes. Translation Axis 3D AxisType3D::Enum The axis along which the position is set. Possible values: AxisX, AxisY,, AxisZ This property is only available for 3D scenes. Set Rotation Expects a Float value as an event. Rotates Rotation Node clockwise by the received value in degrees. Example Usage Set Rotation Example Common Properties Property Name Type Description Target Node Candera::AbstractNodePointer The node which is modified. If not set, then the node where the behavior is attached to, will be modified. RotationAxis AxisType3D::Enum The axis to rotate the node around. Possible values: AxisX, AxisY,, AxisZ This property is only available for 3D scenes.  Set Scale Expects a Float value as an event. Scales Scaled Node by the received (scalar) value multiplied by Vector (X value for horizontal scaling, Y value for vertical scaling). Scaling along either axis can be enabled or disabled. Example Usage Set Scale Example Common Properties Property Name Type Description TargetNode Candera::AbstractNodePointer The Node which is modified. If not set, then the node where the behavior is attached to, will be modified. ScaleAlongX bool Enables or disables scaling in horizontal direction. ScaleAlongY bool Enables or disables scaling in vertical direction. ScaleAlongZ bool Enables or disables scaling in Z-direction. This property is only available for 3D scenes. ScaleVector2D Vector2 This vector is multiplied by the received value and specifies the magnitude by which the node is scaled. This property is only available for 2D scenes. ScaleVector3D Vector3 This vector is multiplied by the received value and specifies the magnitude by which the node is scaled. This property is only available for 3D scenes. Move Node Expects a Float value as an event. Translates Translated Node by the received (scalar) value multiplied by Vector X Y (Z). Example Usage Move Node Example Common Properties Property Name Type Description Target Node Candera::AbstractNodePointer The node TranslateProcessBehavior moves. Multiplied Vector Vector3 This vector is multiplied by the value TranslateProcessValueBehavior receives and specifies direction and magnitude by which TranslateProcessValueBehavior moves Translated Node. If not set, then the node where the behavior is attached to, will be modified. AnimationMeter This behavior is a Behavior Block. It can be dragged&dropped on nodes just like any Behavior. Controls an animation according to the passed value. Property Name Type Description Animation Candera::Animation::AnimationPlayer TThe animation controlled. AnimtionMeter sets the animation to the frame corresponding to a mapped value it receives. Minimum FeatStd::Variant Minimum of the Variant value which will be mapped between 0 and 1. Maximum FeatStd::Variant Maximum of the Variant value which will be mapped between 0 and 1. Arithmetic Operation Arithmetic operation behavior allows to perform addition, subtraction, multiplication and division operations on the passed value. Common Properties Property Name Type Description Operation ArithmeticOperationType::Enum Arithmetic operation to be performed. Possible values: Addition, Subtraction, Multiplication, Division, Modulo, Absolute Operand FeatStd::Variant A number to be used as addend/subtrahend/multiplicant/divisor on provided value. OutputType VariantValueType::Enum Type of the Variant forwarded as result. Possible values: FloatValue, Int32Value, UInt32Value, BoolValue, DoubleValue, Int8Value, Int16Value,  Int64Value, UInt8Value, UInt16Value, UInt64Value, StringValue Receivers Candera::ProcessValueBehaviorArrayProperty The process value behaviors that will receive the value as next in the value processing chain. This property can be set in the right side of the Scene Tree panel. Clock Converts a time integer into seconds, minutes and hours and passes those values to behavior-properties. Common Properties Property Name Type Description SecondsProcessValueBehavior Candera::ProcessValueBehavior* The behavior that receives the seconds. This property can be set in the right side of the Scene Tree panel. MinutesProcessValueBehavior Candera::ProcessValueBehavior* The behavior that receives the minutes. This property can be set in the right side of the Scene Tree panel. HoursProcessValueBehavior Candera::ProcessValueBehavior* The behavior that receives the hours. This property can be set in the right side of the Scene Tree panel. OffsetInMinutes FeatStd::Int32 Offset in minutes to add to time (i.e. for different time zones). ShowFull24Hours bool If true, hours will be shown from 0-23, otherwise in AM/PM format. AMText FeatStd::String The string of the AM label. PMText FeatStd::String The string of the PM label. AMPMTextBehavior Candera::Behavior* Sets text 'AM' or 'PM'. This property can be set in the right side of the Scene Tree panel. ShowSeconds bool If true, seconds will be shown. SecondsNode Candera::AbstractNodePointer The node that will be turned off if showing of seconds is disabled. Dial Receives an angle from a ProcessValueEvent or a value in a ChangeValueEvent. The knob changes its rotation according to that angle. The Behavior Transmits the changed value through events (ValueChangedEvent and ProcessValueEvent). This behavior is available for 2D scenes only. Common Properties Property Name Type Description CurrentValue FeatStd::Int32 Current value for the dial. MinimumRotation FeatStd::Float Minimum rotation of the dial. MaximumRotation FeatStd::Float Maximum rotation of the dial. StepSize FeatStd::Float Step size in degrees. KnobNode Candera::AbstractNodePointer Knob node which will be rotated. Receivers Candera::ProcessValueBehaviorArrayProperty The process value behaviors that will receive the value as next in the value processing chain. This property can be set in the right side of the Scene Tree panel. Filter Filters the processed value via an attached Condition (e.g. Check processed Value). Common Properties Property Name Type Description Condition Candera::ConditionBehavior* ConditionBehavior for passing the value to the next process value behavior. Receivers Candera::ProcessValueBehaviorArrayProperty The process value behaviors that will receive the value as next in the value processing chain. This property can be set in the right side of the Scene Tree panel. Forward Value Forwards a received value to the associated target (associated controls with a value property). Receives a ValueChanged-Event (change notification) and forwards it as a ChangeValue-Event(change request) to the target. The common usecase is to send the Value from a Value behavior to another Value behavior(or Control with a Value).  Emits a ChangeValueEvent which will be received by a Value Behavior. Note that the target Value - Behavior must have 'Accept Value Event' property enabled. Example Usage Forward Value Example Thermometer Example Common Properties Property Name Type Description Event Dispatch Strategy EventDispatchStrategyType::Enum The way the event gets sent. Possible values: Direct, Broadcast, Bubble, Tunnel, DedicatedBehavior Target Node Candera::AbstractNodePointer The target node to which the events are routed. If this property is not set, the event will be routed to the node of the behavior. Dedicated Behavior Candera::ProcessValueBehavior* The dedicated process value behavior that will receive the change value event. This property can be set in the right side of the Scene Tree panel. Interpolate Value Expects a Float value as an event. This behavior holds an internal Float value. It changes this internal value with given speed (Units Per Second) until it reaches the received value. Unless received value matches internal value, it sends internal value to a Process Value Behavior every frame. If the Animation Mode property is set to Instant, no interpolation will be taking place - the received value will be applied immediately. Example Usage Interpolate Value Example Set Scale Example Common Properties Property Name Type Description Animation Mode InterpolationAnimationMode::Enum Animation mode sets a specific interpolation type. Possible values: SpeedBased, TimeBased, Instant Units Per Second Float Speed at which InterpolateProcessValueBehavior changes its internal value. This property can only be set when AnimationMode is set to "SpeedBased". Interpolation Time UInt32 Time in ms the InterpolateProcessValueBehavior changes its internal value. This Property can only be set when AnimationMode is set to "TimeBased" Filter Time Constant Float The moment before InterpolateProcessValueBehavior’s internal value reaches the received value, the speed at which the former is changing slows down. This prevents a sudden end of movement that can be felt as artificial in some cases. This property can only be set when AnimationMode is set to either "SpeedBased" or "Timebased". Receivers Candera::ProcessValueBehaviorArrayProperty The process value behaviors that will receive the value as next in the value processing chain. This property can be set in the right side of the Scene Tree panel. Map Value Expects a Float value as an event. Maps the received value from one interval to another. Common Properties Property Name Type Description InputMin FeatStd::Optional< FeatStd::Variant > [Optional] Smallest value of the interval to check. If Minimum is given as greater than Maximum then the values are internally swapped. InputMax FeatStd::Optional< FeatStd::Variant > [Optional] Largest value of the interval to check. If Maximum is given as smaller than Minimum then the values are internally swapped. OutputMin FeatStd::Float Smallest value of the interval mapped to. OutputMax FeatStd::Float Largest value of the interval mapped to. OutputType VariantValueType::Enum Type of the Variant forwarded as result. Possible values: FloatValue, Int32Value, UInt32Value, BoolValue, DoubleValue, Int8Value, Int16Value,  Int64Value, UInt8Value, UInt16Value, UInt64Value, StringValue Receivers Candera::ProcessValueBehaviorArrayProperty The process value behaviors that will receive the value as next in the value processing chain. This property can be set in the right side of the Scene Tree panel. Map Value Normalized Maps the numeric value received via 'ProcessValueEvent' within an arbitrary range to the normalized range from 0.0 to 1.0 and dispatches the result locally to its receivers. Receivers of this Behavior must therefore be value processing behaviors operating on normalized values. Common Properties Property Name Type Description Reverse bool Toggles the mapping direction. If this property is true, the received value is assumed to be within range from 0.0 to 1.0 and the emitted value is mapped accordingly. ValueForRange ValueBehaviorBase* The input value behavior for defining the mapped range. This property can be set in the right side of the Scene Tree panel. Receivers Candera::ProcessValueBehaviorArrayProperty The process value behaviors that will receive the value as next in the value processing chain. This property can be set in the right side of the Scene Tree panel. Process Value Changed Event This behavior handles ValueChanged events and processes the new value within a set of ProcessValueBehaviors chains. By default ProcessValueChangedBehavior does consume the event, which will result in dispatching the event any further in the dispatching strategy. If further dispatching of the ValueChangedEvent is required set the ConsumeEvent flag to false. Example Usage Process Value Changed Event - Slider Example Process Value Changed Event - State Machine Example Common Properties Property Name Type Description Sender Candera::AbstractNodePointer The node for which the event shall be emitted. If it is not set then the TargetNode or Node (if TargetNode is not set) will be taken instead. Minimum Optional Minimum threshold of the processed values. Maximum Optional Maximum threshold of the processed values. ConsumeEvent bool Set this flag to false if the event should not be consumed by the trigger. By default it is set to true and if the trigger evaluates to true the event will not be routed to any other behavior. Receivers ProcessValueBehavior ArrayProperty The process value behaviors that will receive the value as next in the value processing chain. This property can be set in the right side of the Scene Tree panel. Render a Range This behavior is a Behavior Block. It can be dragged&dropped on nodes just like any Behavior. Renders a range of nodes according to the passed value. Property Name Type Description OperationMode OperationModeType Enum When set to MultipleNodes, EnableNodesProcessValueBehavior will enable the first N children of Group Node. When Operation Mode is set to SingleNode, only Nth node is enabled. N is a number from 0 to number of all children nodes of Group Node. It corresponds linearly to the value EnableNodesProcessValueBehavior receives. Minimum Optional< FeatStd::Variant > Minimum of the Variant value which gets mapped between 0 and 1. Maximum Optional< FeatStd::Variant > Maximum of the Variant value which gets mapped between 0 and 1.   Send ChangeValue on receiving ProcessValue event Sends out a new value. Associated controls with a value property receive the new values. Common Properties Property Name Type Description ChangeValue ChangeValue::Enum How the event value shall be handled by the receiving behavior Target Node Candera::AbstractNodePointer The target node to which the events are routed. If this property is not set, the event will be routed to the node of the behavior. This property is only visible if EventDispatchStrategy is set to "Direct", "Broadcast", "Bubble" or "Tunnel". EventDispatchStrategy CgiStudioControl::EventDispatchStrategyType::Enum The way the event gets sent Possible values: Direct, Broadcast, Bubble, Tunnel, DedicatedBehavior DedicatedBehavior Candera::ProcessValueBehavior* The dedicated process value behavior that will receive the change value event. This property can be set in the right side of the Scene Tree panel. This property only visible if EventDispatchStrategy is set to "DedicatedBehavior". Receivers ProcessValueBehavior ArrayProperty The process value behaviors that will receive the value as next in the value processing chain. This property can be set in the right side of the Scene Tree panel. Set Selected State This behavior is a Behavior Block. It can be dragged&dropped on nodes just like any Behavior. Sets the state to selected or deselected according to the passed value. Smooth Value Class Reference Expects a numeric value as an event and applies exponent smoothing to that value and the previous calculated one. Common Properties Property Name Type Description SmoothingFactor FeatStd::Float The factor how fast the output value should adapt to the input value. Valid values are between 0.0 and 1.0 Receivers ProcessValueBehavior ArrayProperty The process value behaviors that will receive the value as next in the value processing chain. This property can be set in the right side of the Scene Tree panel. Render Child Nodes Enables/Disables Child nodes corresponding to the received value and the behavior settings. Common Properties Property Name Type Description TargetNode Candera::AbstractNodePointer The Node which is modified. If not set, then the node where the behavior is attached to, will be modified. OperationMode OperationMode::Enum When set to MultipleNodes, EnableChildNodes will enable the first N children of Group Node. When Operation Mode is set to SingleNode, only the Nth node is enabled. Possible values: MultipleNodes, SingleNode Levels FeatStd::UInt8 Number of levels to step down through groups. Default is zero. NormalizeValue bool If set to true, the received value has to be between 0 and 1 and will be mapped to the number of children. Otherwise the value has to be the index of the child. Format String 'Format String' modifies the Text of a TextNode Node and provides the Text as property for Controls. It supports formatted text that can display one variable. Example Usage Format String Example Interpolate Value Example Common Properties Property Name Type Description Text String Text that TextBehavior will change the Node to. Supports formatting for one variable that corresponds to the value TextProcessValueBehavior2D receivers. Style SharedPointer The style that will be set to the Text Node. Alignment TextNode2DLayouter::TextAlignment The horizontal text alignment, using the culture text direction, is used to define how text will be horizontally aligned within its layout area. Possible values: Auto, Left, Center, Right Multiline bool If multi line is disabled, then the new line control characters will be ignored and text will always be rendered in one line. Line Spacing PixelSize (UInt16) Defines the distance between the baselines of successive lines of type. Word Wrap Bool If word wrapping is enabled then the lines that exceed the client area will be split during arrangement into multiple lines. Trimming TextNode2DLayouter::Trimming Trimming defines the behavior to employ when content overflows the content area. Possible values: None, Ellipsis, CustomText TrimmingText FeatStd::String Trimming text defines the text which replaces content overflowing the content area. This property is only visible if Trimming is set to "CustomText". TargetNode Candera::AbstractNodePointer The Node which gets the given text. If not set, then the node where the behavior is attached to, will be modified. Track Angle on Drag Listens to the touch of the selected node, returns the angle between pressing, moving and releasing. Common Properties Property Name Type Description TouchNode Candera::AbstractNodePointer A node that is used to collect information about the touch. Receivers ProcessValueBehavior ArrayProperty The process value behaviors that will receive the value as next in the value processing chain. This property can be set in the right side of the Scene Tree panel. Drag on Track to Value Determines the position of a touch move in relation to the associated node and provides it as value in range from 0.0 to 1.0 (normalized). The horizontal boundary of the associated node is the track. The Dragged Node is used to determine the hit area and to determine the position change relative to its center. This behavior can be used as a source to a Value Behavior. Add a Value Behavior as a receiver. Common Properties Property Name Type Description TargetNode Candera::AbstractNodePointer The Node which gets the given text. If not set, then the node where the behavior is attached to, will be modified. UseCenter bool If true, the center value defined for the knob bitmap is used to align the knob to the value position, otherwise the calculated center. TrackDirection TrackDirection::Enum Defines if the position will be tracked horizontally or vertically Possible values: Vertical, Horizontal LeftTouchMargin FeatStd::Float Defines the size for extending or shrinking the touch-sensitive area at the left border of the knob. The size is given in percentage of the knob width. Positive values extend, negative values shrink the area. RightTouchMargin FeatStd::Float Defines the size for extending or shrinking the touch-sensitive area at the right border of the knob. The size is given in percentage of the knob width. Positive values extend, negative values shrink the area. TopTouchMargin FeatStd::Float Defines the size for extending or shrinking the touch-sensitive area at the top border of the knob. The size is given in percentage of the knob height. Positive values extend, negative values shrink the area. BottomTouchMargin FeatStd::Float Defines the size for extending or shrinking the touch-sensitive area at the bottom border of the knob. The size is given in percentage of the knob height. Positive values extend, negative values shrink the area. OnKnobDragOnly bool The position will only be updated when the Knob gets dragged, otherwise clicking on the control will move the knob to the position. UseExcclusiveMode bool Enabling the option prevents some controls (e.g. Slider) from loosing the touch when leaving the node area. DraggedNode Candera::AbstractNodePointer Defines the node to move along the track, to determine the hit area and to determine the position change relative to its center. Receivers ProcessValueBehavior ArrayProperty The process value behaviors that will receive the value as next in the value processing chain. This property can be set in the right side of the Scene Tree panel. Action on Value Passes a Process Value to a Condition Behavior and if the response is positive, invokes an Action behavior. Example Usage Thermometer Example Common Properties Property Name Type Description Condition ConditionBehavior* The ConditionBehavior that TriggerBehavior passes a value to and expect a response from to see if Action needs to be invoked. Actions ActionBehaviorArrayProperty The set of ActionBehaviors that TriggerBehavior invokes in the event that it receives a positive response form Condition. Consume Event bool Set this flag to false if the event should not be consumed by the trigger. By default it is set to true and if the trigger evaluates to true the event will not be routed to any other behavior. Value ValueBehavior sends a value to any behavior derived from ProcessValueBehavior type. It supplies an input to process value behaviors via event. Example Usage Thermometer Example Format String Example Interpolate Value Example Move Node Example Set Alpha Value Example Set Position Example Set Rotation Example Switch Image Example Set Scale Example Common Properties Property Name Type Description Minimum FeatStd::Optional< FeatStd::Variant > Minimum of the Variant value. If Minimum is given as greater than Maximum then the values are internally swapped. Maximum FeatStd::Optional< FeatStd::Variant > Maximum of the Variant value. If Maximum is given as smaller than Minimum then the values are internally swapped. IntervalHandling IntervalHandling::Enum Select how the behavior should react when the minimum or maximum limit is exceeded. Possible values: Limit, Cycle, Ignore AcceptValueEvent bool Set this flag to true to make the value changeable by events/actions. BroadcastProcessValueEvent bool Set this flag to true to broadcast ProcessValue event even if value did not change. DispatchStrategy CgiStudioControl::EventDispatchStrategyType::Enum By default the event that indicates that this value behavior has been changed (ValueChangedEvent) is dispatched only on the node to which the value behavior is attached (CgiStudioControl::EventDispatchStrategyType::Direct). To change this you have to select a different dispatch strategy. Possible values: Direct, Broadcast, Bubble, Tunnel, DedicatedBehavior DedicatedBehavior Candera::Behavior* The dedicated behavior that will receive ValueChangedEvent when DedicatedBehavior dispatch strategy is selected. This property is only visible if DispatchStrategy is set to "DedicatedBehavior". This property can be set in the right side of the Scene Tree panel. TargetNode Candera::AbstractNodePointer The node on which the for which the EventDispatchStrategy will be applied. If it is not set then the Node will be taken instead. This property is only visible if DispatchStrategy is set to "Direct", "Broadcast", "Bubble" or "Tunnel". Variant Candera::Variant Specifies the type and the value to pass onto Process Value Behavior. Receivers ProcessValueBehavior ArrayProperty The process value behaviors that will receive the value as next in the value processing chain. This property can be set in the right side of the Scene Tree panel. Value Generator The Value Generator is a demo behavior. It allows you to configure minimum and maximum values, period, and update interval, and is used for UI verification and simulation purposes. It appears in the tool when CONTROLS_DEMO_BEHAVIORS_ENABLED is enabled via CMake. Related page: Control Behaviors Flags Common Properties Property Name Type Description GeneratorFunction Enum The type of function used to generate values (linear, sin, etc.) Minimum Float The minimum for the generated values. Maximum Float The maximum for the generated values. OffsetMs Int The time offset where the function is evaluated. PeriodMs Int The time period after which the generated values repeat. SamplerateMs Int The update rate of the generated value. GenerateValues bool Set this flag to true to generates values at sample rate. If set to false, no values are generated. Event Dispatch Strategy EventDispatchStrategyType::Enum The way the event gets sent. Possible values: Direct, Broadcast, Bubble, Tunnel, DedicatedBehavior Dedicated Behavior Candera::ProcessValueBehavior* The dedicated process value behavior that will receive the change value event. This property can be set in the right side of the Scene Tree panel. Target Node Candera::AbstractNodePointer The target node to which the events are routed. If this property is not set, the event will be routed to the node of the behavior.